Free Shipping on Ground shipments and Commercial Freight Shipments!!!! Restrictions Apply

Store

Our Products: Caterpillar

Cat 279C 289C 289C Tracks- 60 Links

Cat 279C2 289C 289C2 Rubber Track
Rubbertrax
Cat 279C 289C 289C Tracks- 60 Links
Buy aftermarket replacement rubber tracks for Caterpillar 279C, 289C, and 289C compact track loaders. This is the 400mm (16 inch) wide rubber track option for the Cat® track loaders and is commonly found on the D3 series of these models as well. This is the sixty drive link option.
SKU: RTC408660
Weight: 550 lbs
Make: Cat
Shipping: Fast and Free!
Price: $2,370.00

Product Details

This is the optional size for the staggered block tread pattern aftermarket replacement rubber track for Caterpillar® compact track loaders. The tread pattern shown is the most common but other tread pattern options are available. This is our staggered block tread pattern for maximum floatation in general use applications. The track sixteen inches wide with SIXTY metal links down the center of the track. This is the most common size for the specified Caterpillar below and additionally fits most of the D3 series models. There is an optional FIFTY-SIX link track so please check the number of metal links on your track prior to ordering. We do stock the eighteen inch version as well under part number CAT-0507 (56 links) or MEPC-0512 (60 links).

You must verify width of track and number of links prior to ordering. If your track is sixteen inches wide with sixty drive links then this is the correct track for your specific machine. If your track is sixteen inches wide with fifty-six links you need the 400x86x56 size.


This rubber track is known to fit the following models as the narrow option:

  • Caterpillar® 279 C
  • Caterpillar® 279 C2
  • Caterpillar® 289 C Serials JMP
  • Caterpillar® 289 C2
  • Caterpillar® 299 C
  • Caterpillar® 299 D
  • Caterpillar® 299 D3
  • Caterpillar® 299 D2
  • Caterpillar® 299 DXP

Alternate Part Numbers

  • Caterpillar® Dealer Part Number: 545-6421, 592-5830, 592-5829

Rubber Track Options

This track comes in a 450mm (18 inches) width with 56 links and a 450mm (18 inches) width with 60 links also. Please call for details and to verify if the additional width will work on your machine. This track is generally available in our staggered block tread pattern however other tread patterns may be available upon request.

Alternate Models

This rubber track (592-5830) is known to fit:

  • Takeuchi TL12R2
  • Takeuchi TL12V2 (SN#412000579 & Up)

Reliable Track Quality

Our rubber tracks are made with helically wound continuous steel cords that are coated for protection against rust that are designed for reliable service in rigorous conditions. We use non-recycled rubber in our most technologically advanced factory that strives to bring continuous improvements to our quality products.

This track comes with a standard warranty against manufacturer defects. If sprockets are purchased and installed together with the tracks it will extend the lifespan of your tracks.



Always consider changing your sprockets and any worn undercarriage parts when you change your tracks. Rubber tracks and sprockets are designed to wear together and changing sprockets at any other time would reduce the lifespan of both the track and the sprocket. Other worn parts can effect the tensioning of the track and can cause de-tracking and other wear issues.


Tread Patterns Commonly Available

Staggered Block Tread Pattern

The off-set block tread pattern is the most general purpose tread pattern for wide spread job site applications. Adequate traction with maximum floatation helps prevent damage to sensitive areas while still providing enough traction for typical job sites.

Zig Zag Tread Pattern

This tread pattern allows for maximum traction in a wide variety of applications including mud, snow, and slopes. The additional tread depth gives you more forward traction with just enough jagged zig zag edges to provide traction on a slide slope.